โšก UPDATES
PG in EV & Embedded Systems โ€” IIT Jammu (12 Months) Flagship M.Tech in EV Technology โ€” 24 Month Program Open DET Entrance Test โ€” Unlock Scholarship Up to โ‚น50,000 Scholarship 95,000+ Professionals Trained Nationwide Placement Drive โ€” 320+ Hndustry Partners ASDC & AICTE NEAT Certified Programs PG in EV & Embedded Systems โ€” IIT Jammu (12 Months) Flagship M.Tech in EV Technology โ€” 24 Month Program Open DET Entrance Test โ€” Unlock Scholarship Up to โ‚น50,000 Scholarship 95,000+ Professionals Trained Nationwide Placement Drive โ€” 320+ Hndustry Partners ASDC & AICTE NEAT Certified Programs
Accredited by
NEAT AICTE Ministry of Education ASDC
DIYguru
โšก Apply Now โ€” PG & Nanodegree Programs Open DET Entrance Test โ€” Get Scholarship up to โ‚น50,000
๐Ÿ“…
Bharat eMobility Recruitathon 2026 Delhi: Mar 21-23 | Pune: May 21-24

DIYguru  โ€บ  EV Guides  โ€บ  Motor Controllers

EV Motor Controller Guide: How It Works, Wiring, Error Codes & Sizing (India 2026)

EV motor controller operation explained for technicians, mechanics and engineers: what's inside a scooter or e-rickshaw controller, FOC vs square-wave, MOSFET vs IGBT vs SiC, regenerative braking, wiring every connector, and fixing common faults. Includes a free error-code lookup and a controller sizing tool.

By DIYguru EV Service Team Updated 24 October 2026 24 min read
0 of 9 chapters reviewedSearch glossary

The short answer

A EV motor controller (also called an inverter or drive) sits between the battery and the motor. It reads the throttle, brake and motor position sensors, then switches six power transistors (MOSFETs in scooters and e-rickshaws, IGBTs or SiC MOSFETs in cars) thousands of times a second to feed the motor three-phase current. Simple controllers use square-wave (six-step) control; better ones use sine-wave FOC, which is smoother, quieter and more efficient. Controllers also handle regenerative braking and protect the system against over-current, low voltage and overheating, which is where most error codes come from.

Contents

In this guide

Chapter 1

What an EV motor controller does

INTERACTIVE WALKTHROUGH

Follow the signal and energy paths

Energy moves through the power stageBattery DCControllerMotor phases
Energy moves through the power stage. Simplified teaching model, not a wiring schematic.
  1. The rider requests torque through the vehicle controls.
  2. The EV motor controller checks operating limits and feedback.
  3. Gate drivers command the power switches.
  4. Controlled phase currents produce motor torque.
  5. Feedback updates the next command.
Why battery current and phase current differ

Battery current describes DC input. Phase currents flow through motor windings and change during switching. They are not interchangeable ratings, and no fixed multiplier applies at every operating point.

The EV motor controller is the vehicle's power manager: it decides how much current flows from the battery to the motor, and when.

Controller block diagram: battery feeds DC link capacitors and a six-switch power stage that drives the three-phase motor; a microcontroller reads throttle, brake and Hall sensors and drives the switches through gate drivers, with current and temperature sensing for protection Battery 48โ€“72 V DC MOTOR CONTROLLER DC link capacitors Power stage 6 MOSFETs / IGBTs Current sensors Microcontroller + gate drivers Protection V ยท I ยท temp Motor U V W Throttle Brake switch Key / modes Hall sensors
Figure 1. Inside a typical controller. The power stage switches battery current into the motor's three phases (U, V, W); the microcontroller decides when, based on throttle, brake and motor-position (Hall) signals, and shuts things down if voltage, current or temperature go out of range.

Its five jobs

  • Power conversion: turns battery DC into three-phase AC (variable frequency and amplitude) for the motor.
  • Torque and speed control: converts the throttle position into a motor current request, with ramps for smooth starts.
  • Commutation: uses Hall sensors, an encoder or sensorless estimation to know where the rotor is and energise the right windings.
  • Regenerative braking: runs the motor as a generator to slow the vehicle and recharge the battery.
  • Protection and diagnostics: limits current, cuts out at low or high voltage, reduces power when hot, and reports faults as error codes or LED blinks.
Chapter 2

How an EV motor controller drives the motor: the three-phase bridge and PWM

INTERACTIVE WALKTHROUGH

Adjust PWM duty cycle

PWM pulse width changes with duty cycleONE IDEALISED SWITCH NODE
PWM pulse width changes with duty cycle. Simplified teaching model, not a wiring schematic.

This model switches between 0 V and 48 V. Average switch-node voltage = duty ร— DC bus voltage. It does not predict motor speed or line-to-line motor voltage.

Why complementary switches need dead time

A short non-overlap interval helps prevent the high-side and low-side devices in the same leg conducting simultaneously. The required timing depends on the devices, driver and hardware; this illustration does not specify it.

Six switches, two per phase, connect each motor wire to either the battery's positive or negative terminal.

Three-phase inverter bridge: three legs each with a high-side and low-side switch between battery positive and negative; the midpoint of each leg connects to motor phase U, V or W B+ Bโˆ’ Q1Q3Q5 Q2Q4Q6 UVW UVW Motor DC link caps High-side switches on top, low-side below. Never on together in the same leg (that's a "shoot-through" short).
Figure 2. The three-phase bridge. By switching the high-side and low-side transistors of each leg on and off with PWM (pulse-width modulation), typically at 8โ€“20 kHz, the controller builds the current waveform each motor phase needs.

PWM (pulse-width modulation) controls how much voltage the motor "sees": switching the transistors on for a larger share of each cycle (a higher duty cycle) gives more voltage and more current. Between transistors, the gate driver adds a tiny dead-time so the high-side and low-side switches of one leg are never on together.

Why controllers "blow"A shorted MOSFET is the most common hard failure. Typical causes are a phase-wire short, water ingress, an EV motor controller pushed beyond its current rating on steep climbs or with overloading, voltage spikes from a battery disconnected while running, or poor cooling. A controller with a shorted MOSFET often makes the motor hard to turn by hand even with the power off.

Chapter 3

Square-wave vs sine-wave vs FOC controllers

INTERACTIVE WALKTHROUGH

Explore the control approaches

Feedback and switching work togetherCurrent feedbackControl algorithmGate commands
Feedback and switching work together. Simplified teaching model, not a wiring schematic.

Motor design, position information, tuning and thermal conditions all affect the result. An EV motor controller label alone cannot guarantee smoothness or efficiency.

Square-wave (six-step)Sine-waveFOC (field-oriented control)
How it worksEnergises two phases at a time in 6 steps, using Hall sensorsShapes the phase current into a sine waveMeasures phase currents and controls torque-producing and flux-producing current separately
Smoothness & noiseSome vibration and whine at low speedSmoother and quieterSmoothest and quietest
EfficiencyGoodBetterBest across the speed range
Extra featuresBasicSome regen and speed modesField weakening for higher top speed, precise regen, sensorless operation
CostLowestMediumHigher
Typical useBudget e-rickshaws, e-cyclesMid-range scooters, newer e-rickshawsPremium scooters and motorcycles, all cars

FOC in plain words

A motor's current can be split into two parts: one that produces torque (called Iq) and one that adds to or opposes the magnets' field (Id). FOC continuously measures the phase currents, uses the rotor position to translate them into Iq and Id, and controls each independently, many thousands of times a second. The result is smooth torque from zero speed, the best efficiency, and the ability to weaken the field (negative Id) to push the motor past its normal top speed.

Upgrading a vehicle?Replacing a square-wave EV motor controller with a sine-wave or FOC controller of the same voltage and current rating usually makes a hub-motor scooter or e-rickshaw quieter and slightly more efficient. Match the voltage, current, Hall sensor type and connector pinout, and expect to run the controller's phase/Hall learning routine.

Chapter 4

MOSFET vs IGBT vs SiC vs GaN: the power switches

INTERACTIVE WALKTHROUGH

Trace heat through the assembly

Heat must leave the power stagePower switchesThermal interfaceHeatsink / coolant
Heat must leave the power stage. Simplified teaching model, not a wiring schematic.
Two loss mechanisms

Conduction losses occur while current flows through a switch. Switching losses occur during transitions. Increasing switching frequency can increase transition losses; actual performance depends on device and operating conditions.

Read the datasheet as a system

Check voltage transients, current definition, gate drive, cooling, switching conditions and junction-temperature limits together. A headline device current rating is not the completed EV motor controller rating.

The power transistors decide how much current an EV motor controller can handle, how hot it gets and how efficient it is.

DeviceTypical voltage classSwitching speedStrengthsWhere it's used
Silicon MOSFETUp to ~150 V (in EV drives)Fast (tens of kHz)Very low losses at low voltage, cheap, easy to parallelAlmost all scooters, motorcycles and e-rickshaws (48โ€“96 V)
IGBT600โ€“1,200 VMedium (up to ~20 kHz)Robust, handles high voltage and current, matureMany electric cars, buses and industrial drives
SiC MOSFET650โ€“1,700 VFastLower losses than IGBT, runs hotter, smaller cooling; boosts range a few percentNewer 400 V and especially 800 V cars and fast chargers
GaN transistorUp to ~650 VVery fastExtremely low switching loss, compactOn-board chargers and DC-DC converters today; traction inverters emerging

A scooter EV motor controller labelled "72 V 60 A" might use 12โ€“24 MOSFETs in parallel, rated around 100โ€“150 V, mounted on an aluminium plate that doubles as the heatsink. A car inverter at 350โ€“800 V uses IGBT or SiC power modules with liquid cooling.

Chapter 5

Regenerative braking: how controllers recover energy

INTERACTIVE WALKTHROUGH

See how battery acceptance limits regen

Regenerative energy flowMotor generationControllerBattery acceptance
Regenerative energy flow. Simplified teaching model, not a wiring schematic.

For this simplified model, accepted power is the smaller of requested power and battery allowance. Real systems also limit regen by speed, traction, voltage and temperature. Friction braking remains necessary; regen is not guaranteed.

When you release the throttle or press the brake, the EV motor controller changes the switching pattern so the spinning motor generates current instead of using it. That current flows back through the controller into the battery, creating a braking force. In stop-start city traffic this can recover a useful share of energy and reduce brake wear.

  • Regen fades at low speed: there's little energy to recover below about walking pace, so mechanical brakes always finish the stop.
  • No regen when the battery is full: the BMS blocks charging current, so regen is reduced or disabled at 100%.
  • Lead-acid batteries accept regen poorly, and over-voltage during long descents can trip the EV motor controller. Lithium packs accept it better, within the BMS charge-current limit.
  • Settings matter: most programmable controllers let you set regen strength, the brake-switch trigger and the maximum regen current.

Over-voltage riskNever disconnect the battery while the vehicle is rolling. With no battery to absorb regen current, the voltage inside the EV motor controller can spike and destroy the MOSFETs.

Chapter 6

EV EV motor controller wiring explained: every connector

INTERACTIVE WALKTHROUGH

Series and parallel: understand the supply

Identical example cells: 3.2 V nominal, 5 Ah. Series adds voltage; parallel adds capacity. This arithmetic illustration is not a pack construction guide. Actual series count, full-charge voltage and BMS limits must come from the pack specification.

Most scooter and e-rickshaw controllers in India follow the same pattern. Colours vary by brand, so always confirm with the label or a multimeter.

Typical controller wiring: battery through fuse and key switch to controller power input; three thick phase wires and a five-wire Hall harness to the motor; throttle, brake, key, reverse and speed-mode switches and display connected to signal inputs Battery pack FUSE CONTROLLER B+Bโˆ’ Motor (Hall sensors inside) Phases U V W Hall: 5V ยท GND ยท A ยท B ยท C Throttle Brake switch Key switch Reverse Speed modes Display / CAN Key switch wire: small B+ feed that wakes the controller (often thin red / orange)
Figure 3. Typical controller wiring for an electric scooter or e-rickshaw. Thick wires carry power (battery and phases); thin wires carry low-voltage signals. Exact colours and pin positions vary, so check your controller's label.
ConnectionCommon colours*What it doesTypical reading
Battery B+ / Bโˆ’Red / Black (thick)Main power input, through a fusePack voltage, e.g. 48โ€“58 V on a 48 V LFP pack
Phase U, V, WYellow, Green, Blue (thick)Three-phase power to the motorEqual resistance between each pair (battery off)
Hall sensor harnessRed 5 V, Black GND, Yellow / Green / Blue signalsTells the controller the rotor position5 V supply; each signal switches between ~0 V and ~5 V as the wheel turns
ThrottleRed 5 V, Black GND, Green (or white/blue) signalSpeed requestSignal ~0.8โ€“0.9 V at rest to ~4 V at full throttle
Brake (e-brake / cut-off)Varies, 2 wiresCuts motor power, can trigger regenSwitches the signal line to ground (low) or 5 V (high), depending on the controller
Key / ignition (power lock)Thin red or orangeWakes the controller from a small B+ feedPack voltage when the key is on
ReverseVariesReverses the motor at low speed (e-rickshaws, loaders)Grounded or open by the reverse switch
Speed mode (2/3-speed)VariesSelects low / medium / high speed limitsGrounded combinations select modes
Self-learning (phase / Hall learning)Often a pair of same-colour thin wiresConnected briefly, makes the controller detect the motor's phase and Hall sequence automaticallyMotor turns slowly by itself; disconnect when done (follow the manual)
Display / CAN / UARTVariesSpeed, battery level, error codes, programmingโ€“

*Colours are common conventions on Indian and Chinese-made scooter and e-rickshaw controllers, not a standard. Always check the EV motor controller label, and confirm with a multimeter before connecting.

Before you touch any wireFollow the manufacturerโ€™s isolation and lockout procedure and verify absence of voltage; waiting a fixed time does not prove the capacitors are discharged. Connecting a battery to a controller can cause a big spark as the capacitors charge, so use a pre-charge resistor or the controller's key/contactor sequence if it has one.

Free tool

EV EV motor controller Error Code Lookup

Type the code on your display (for example 24, 0x23, E08) or describe the problem (jerking, cuts off on hills, no power). Codes mean different things on different systems, so pick your display type if you know it.

Try:

Get a printable troubleshooting sheet and wiring diagram for your own EV motor controller: size it below, then unlock the sheet.

Go to the sizing tool โ†“

KT-style codes (21โ€“25, 30) are used by many Chinese-made controllers and LCDs; Bafang codes come from Bafang displays. Generic e-rickshaw controllers usually show faults as LED blinks, and the blink meanings are printed on the EV motor controller label. Always confirm with your controller or vehicle manual.

Chapter 7

How to test an EV motor controller with a multimeter

INTERACTIVE WALKTHROUGH

Explore fault scenarios safely

Fault codes are model and firmware specific. The lookup below is a starting point, not a diagnosis. Testing is for trained and authorised personnel using manufacturer procedures, isolation and verified absence of voltage where required. Battery disconnection alone does not establish that stored energy is discharged.

These examples are for trained technicians following the exact manufacturer procedure. Readings vary by circuit. Isolate, lock out and verify absence of voltage before power-off tests; stored energy may remain after disconnection.

TestHowGood resultBad result means
1. Supply voltageKey on, measure B+ to Bโˆ’ at the controllerPack voltage, steady under loadLow or dropping sharply: battery, fuse, connector or key circuit problem
2. Throttle signalKey on, measure signal to GND while twisting~0.8โ€“0.9 V at rest, rising smoothly to ~4 VStuck high (dangerous runaway risk), stuck low, or jumpy: throttle or wiring fault
3. Hall sensorsKey on, 5 V between red and black; probe each signal while turning the wheel slowly by handEach of A, B, C switches between ~0 V and ~5 VA signal stuck at 0 V or 5 V: failed Hall sensor or broken wire
4. Motor phasesBattery off, phases disconnected; measure resistance Uโ€“V, Vโ€“W, Wโ€“U, and each to the motor bodyThree equal low readings; no continuity to the bodyOne pair different: winding or wire fault. Continuity to body: insulation failure
5. Power stage (MOSFETs)Battery off; diode test from Bโˆ’ to each phase and from each phase to B+Similar diode-drop readings on all three phasesNear 0 on any reading: shorted MOSFET, so replace or repair the controller

Quick check for a shorted EV motor controllerWith the battery disconnected, lift the driven wheel and spin it. Then disconnect the three phase wires from the controller and spin again. If the wheel was hard to turn before and spins freely after, a power-stage fault is possible; this observation alone is not conclusive.

Hall sequence and phase matching

When a motor or EV motor controller is replaced, the three phase wires and three Hall wires must be matched. There are 36 possible combinations, and only a couple run the motor correctly in the right direction. Many controllers have a self-learning wire that finds the right combination automatically. Use the manufacturerโ€™s documented commissioning procedure; do not experiment with phase or Hall wiring on an energised system.

Chapter 8

EV motor controller ratings and how to size one

INTERACTIVE WALKTHROUGH

Estimate DC input current

Input current โ‰ˆ mechanical power รท (bus voltage ร— combined efficiency). This steady-state estimate excludes transients and does not select a fuse, cable, phase-current limit or EV motor controller.

How to use the original sizing tool below

Its series-count mapping, cell limits, 2.5ร— phase-current estimate, cable sizes and fuse suggestions are illustrative assumptions. Verify the actual battery configuration and all thermal, fault-interruption and wiring conditions with qualified design review. Do not apply its suggested cut-offs as universal settings.

"48 V 1000 W" on a label tells you less than you think. These are the numbers that matter.

  • Voltage class: must cover the battery's full range, from fully charged to empty. A 48 V LFP pack (16S) reaches about 58 V when full.
  • Battery current limit (A): the maximum current drawn from the battery. Power โ‰ˆ voltage ร— battery current. This is what a "48 V 30 A" label usually means.
  • Phase current limit (A): the current in the motor wires. At low speed it can be 2โ€“3ร— the battery current, and it sets launch and hill-climbing torque.
  • Low-voltage cut-off (LVC): the voltage at which the EV motor controller stops, to protect the battery. It must match the battery chemistry.
  • Control type and sensor: square-wave or sine/FOC; Hall, encoder or sensorless.

Converting an e-rickshaw from lead-acid to lithium?A lead-acid 48 V EV motor controller usually cuts off around 42 V (10.5 V per 12 V battery). A 48 V lithium pack has a different voltage window, so the controller's low-voltage cut-off and maximum voltage must be reset or the controller replaced. Otherwise you risk over-discharging the pack or the BMS cutting power suddenly.

Work out the voltage, battery current, phase current, fuse and cable sizes for your vehicle.

Use the sizing tool โ†“
Free tool

EV EV motor controller Sizing Tool

Enter your battery and motor. You'll get the EV motor controller voltage class, current ratings, low-voltage cut-off, fuse and recommended controller type. Unlock the full sheet to get a wiring diagram for your setup, cable sizes, controller settings, and a step-by-step troubleshooting guide.

1. Your vehicle, battery & motor

Motor ratings are on the motor label or spec sheet. If you only know one number (like "1000 W"), it's usually the rated power; peak is often 1.5โ€“2ร— rated.

2. EV motor controller you need

โ€“

โ€“Peak phase current
โ€“Battery voltage range
โ€“Low-voltage cut-off
โ€“Main fuse
Recommended controllerโ€“

Get your wiring diagram & troubleshooting sheet (free)

A wiring diagram for your exact setup, battery and phase cable sizes, EV motor controller settings to program, an installation checklist, and a step-by-step fault-finding guide with the readings to expect.

Estimates for selection and learning. Always follow the EV motor controller and motor manufacturers' ratings, and have high-current wiring done by a trained technician. Road-going vehicles must keep type-approved components.

Chapter 9

Careers in EV controllers and power electronics

INTERACTIVE WALKTHROUGH

Track your learning

Progress is stored only in this browser and does not certify practical competence.

EV service technician

Diagnoses EV motor controller, Hall, throttle and wiring faults on scooters and e-rickshaws. The most in-demand entry role.

Power electronics design engineer

Designs inverter power stages, gate drivers and protection using MOSFET, IGBT and SiC devices.

Motor control firmware engineer

Writes FOC, sensorless and regen algorithms on microcontrollers in embedded C.

Controller test & validation engineer

Runs dynamometer, thermal, EMC and durability tests on controllers.

Field application engineer

Helps vehicle makers choose, program and integrate controllers.

Workshop owner / retrofit specialist

Repairs controllers, upgrades e-rickshaws and runs an EV service business.

INTERACTIVE WALKTHROUGH

Search the EV motor controller glossary

20 terms

PWM
Pulse-width modulation: controlling pulse duration within a switching period.
Duty cycle
Fraction of a switching period spent in the on state.
DC bus
The DC supply rails feeding the inverter power stage.
Inverter
Power stage converting DC into controlled motor phase voltages.
Gate driver
Circuit that drives the control terminal of a power switch.
Dead time
Non-overlap interval between complementary switching commands.
FOC
Field-oriented control using rotating reference-frame quantities.
Phase current
Current in a motor winding phase, distinct from battery-side current.
Battery current
Current at the DC supply connection.
BMS
Battery management system that monitors and limits pack operation.
Regen
Regenerative operation returning some mechanical energy electrically.
Derating
Reducing allowable output to remain within operating limits.
Hall sensor
A magnetic sensor that can provide rotor position information.
MOSFET
A voltage-controlled semiconductor switch.
IGBT
An insulated-gate bipolar transistor used as a power switch.
SiC
Silicon carbide, a semiconductor material used in power devices.
Series
Identical cells in series add nominal voltage.
Parallel
Identical cells in parallel add ampere-hour capacity.
Precharge
Controlled charging of DC-link capacitance before normal connection.
Shoot-through
Unwanted conduction through both devices in one bridge leg.

EV motor controller references and further learning

Explore the Texas Instruments three-phase inverter reference design to connect the power-stage concepts in this guide with documented hardware. For a protection-focused example, see TIโ€™s isolated three-phase inverter reference design. These are engineering references, not instructions to copy a design into a vehicle.

Continue with DIYguru EV training programs to explore structured learning options. Read the DIYguru course FAQs for common enrolment and learning questions.

Become the technician everyone calls

Learn EV controllers and diagnostics with DIYguru

DIYguru is India's largest ASDC-certified EV skilling organisation, with 95,000+ learners trained. Pick the path that matches where you are today.

Best match for this guide

3 months ยท Professional certification

CEVT: Certified Electric Vehicle Technician

Best for: mechanics, e-rickshaw technicians, ITI and diploma holders moving into EV service.

  • High-voltage safety and multimeter diagnostics
  • EV motor controller, Hall sensor, throttle and wiring fault-finding
  • Battery and BMS checks, 2W/3W EV service
  • Hands-on practicals at DIYguru labs in Delhi and Bangalore
  • ASDC certification ยท Placement Support

3 months ยท Professional certification

Professional Certification in Motor Drive Systems & Control Systems

Best for: engineers and working professionals who want to understand and design motor drives.

  • Inverters, PWM and power devices
  • BLDC, PMSM and induction motor control, including FOC
  • Control systems for EV drives
  • Self-paced, built for working professionals
  • ASDC and AICTE certification ยท Placement Support
FAQ

EV motor controller questions, answered

What does a motor controller do in an electric vehicle?

It converts the battery's DC into three-phase current for the motor, controls torque and speed based on the throttle, uses Hall or position sensors to time the current, handles regenerative braking, and protects the system from over-current, low or high voltage and overheating.

What does error 24 mean on an electric scooter?

On many Chinese-made controllers and KT-style displays, code 24 (0x24) means a motor Hall sensor fault: the EV motor controller isn't getting a correct rotor-position signal. Check the Hall connector, the 5 V supply and each Hall signal. Code meanings differ between brands, so confirm with your manual.

Why is my e-rickshaw or scooter jerking when starting?

Jerking at start is most often a Hall sensor problem, such as a loose connector, broken wire or failed sensor, or a wrong Hall/phase sequence after a repair. Low battery voltage under load and a faulty throttle can also cause it.

What is the difference between square-wave and sine-wave controllers?

A square-wave (six-step) EV motor controller energises two phases at a time, which is simple and cheap but causes some vibration and noise. A sine-wave or FOC controller shapes smooth sinusoidal currents, making the motor quieter, smoother and more efficient, at a higher cost.

How do I know if my motor controller is faulty?

Common signs are no power with good battery voltage, a burning smell, a motor that's hard to turn by hand with the battery disconnected (a shorted MOSFET), repeated over-current codes, or a fuse that keeps blowing. A multimeter diode test from each phase to B+ and Bโˆ’ confirms a shorted power stage.

Can I use a higher-voltage controller on my scooter?

Only if the motor, battery, wiring and other electronics are rated for it. A higher voltage raises top speed and stresses the motor and battery. On road-registered vehicles, changing type-approved components can also void approval and warranty.

What are the wires on a BLDC controller?

Thick battery wires (B+ and Bโˆ’), three thick phase wires to the motor (often yellow, green, blue), a five-wire Hall harness (5 V, ground and three signals), a throttle (5 V, ground, signal), brake cut-off wires, a key or ignition wire, and often reverse, speed-mode, self-learning and display wires.

Do I need to change the controller when converting an e-rickshaw to lithium?

Usually the EV motor controller's low-voltage cut-off and maximum voltage must be reset to suit the lithium pack, or the controller replaced. A lead-acid setting can over-discharge a lithium battery or trigger sudden BMS cut-offs.

Are MOSFETs or IGBTs used in EV controllers?

Low-voltage vehicles such as scooters, motorcycles and e-rickshaws (48โ€“96 V) use silicon MOSFETs. Higher-voltage cars and buses use IGBT or, increasingly, silicon carbide (SiC) MOSFET power modules, especially in 800 V systems.

Fix EVs with confidence and get certified

Talk to a DIYguru advisor about CEVT or the Motor Drive certification. We'll share batch dates, fees and EMI options.

  • Free counselling call within 24 hours
  • Hands-on controller and wiring practice in Delhi and Bangalore labs
  • ASDC-certified training
  • Placement support through emobility.careers

Prefer to call? +91 99109 18719 ยท [email protected]

Get free career counselling

An advisor will call you within 24 hours.

Your details go only to DIYguru. No spam.

Sources & further reading

  1. Electric Bike Review forum: 0x21โ€“0x30 controller / LCD error codes
  2. Upway: Bafang error codes list
  3. Upway: generic e-bike error codes (no universal standard)
  4. Zbotic: Hall sensor wiring and faults
  5. Letrigo: e-bike throttle wiring and signal voltages
  6. Bioenergy Times: IESA on motor technology in Indian EVs

This guide is for education. Error-code meanings vary by manufacturer; always confirm with the controller or vehicle manual. High-voltage work must be done by trained technicians with the battery isolated. ยฉ DIYguru Mobility Pvt. Ltd.